This Damper is used to reduce noise and vibration for Nema 17 stepper motor on your 3D Printer *Made of steel and rubber material, durable and practical. *Easy installation. (Screws are Not included) *Dimension:51.8*51*6mm/2.04’’x1.97’’x0.24’’ (Approx) This Damper is used to reduce noise and vibration...

TL Smoother er til perfektionisten. Den monteres blot på dine stepper motore, og fjerne da streger i dit print, ved at give en blødere stepper kørsel og beskytter samtidigt dit motherbord, mod induceret spænding når du flytter rundt på akserne.  TL-Smoother - forkæl din 3D...

Lodde hylster / Heat Shrink Soldering Sleeve Connector - 10pcs Put de pågældende ledninger ind i hver ende Varm hylsteret op Nu har du loddet dine to ledninger sammen Udover at det er nemt, er denne metode også vandsikker, stødsikker og fleksibel.  Operating Temperatur: -55...

Nema17 stepper kabel, billedet af produkt kan variere.  Nema17 stepper cable

SpiderScrew Mixed Kit with Knurls - M3/M4/M5/M6 Vores nyeste SpiderScrew Kit. 160 pcs M3/M4/M5/M6 skruer og Knurls i forskellige størrelser. M3 nut: 40pcsM4 nut: 40pcsM5 nut: 40pcsM6 nut: 40pcs *20 x M3-6 *20 x M3-10 *20 x M4-6 *20 x M4-10 *10 x M5-6...

A4988 Stepper driver module This product is a carrier board or breakout board for Allegro's A4988 DMOS Microstepping Driver with Translator and Overcurrent Protection by Pololu; we therefore recommend careful reading of the A4988 datasheet before using this product. This stepper motor driver lets...

SpiderScrew Kit with Nuts - M3 Vores nyeste SpiderScrew Kit. 80 stk M3 skruer med tilhørende møtrik i forskellige størrelser: *20 x M3-6 *20 x M3-10 *15 x M3-16 *15 x M3-20 *10 x M3-30 Et 'must have' til din 3D printer SpiderScrew Kit...

L298N Dual H Bridge Stepper Motor Driver Board DC Stepper Motor Drive Controller Board Module For Arduino Low heat,outstanding anti-interference performance. Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors. Built-in 78M05, get power from drive power, however, when...

Model: 42BYGHW811 2.5A Without 4pin cable Technical Specifications  Part No.:                          42BYGHW811   Frame Size:                    NEMA17 Step Angle:                    1.8 degree Voltage:                          3.1V Current:                          2.5 A/phase Resistance:                   1.25Ohm/phase Inductance:                   1.8mH/phase Holding torque:             4800g.cm  70oz-in     Rotor inertia:                  68g-cm2 Detent torque:               280g-cm Number of wire leads:  4 Weight:                            0.34 kg Length:                            48mm Without:  4pin cable

Denne samlemuffe gør det nemt når man eksempelvis skal udskifte/opgradere ens blæser.  Isoleret Crimp / Samlemuffe

Nema17 1.7A Weight: 2600g. Cm: 40mm length 4-Lead 2 phase Stepper Motor. Model: 42BYGHW609 1.7A Without 4pin cable Specifications:Step Angle: 1.8±5% degree/phaseVoltage: 3.6V Current: 1.7A/phaseResistance: 2 Ω/phaseInductance: 3.0mH( 1kHz 1V rms)Comes with 4-Lead WireRotor torque: 54g/cm2Detent torque: 140g.cminsulation resistance:100MΩ Min (50V DC)Insulation class: B Net Weight:...

SpiderScrew Kit - M3 - 80 pcs Vores nyeste Spider Kit. 80 pcs M3 skruer i forskellige længder.  *20 x M3-6 *20 x M3-10 *15 x M3-16 *15 x M3-20 *10 x M3-30 Et 'must have' til din 3D printer SpiderScrew Kit - M3...

28BYJ-48 – 5V Stepper Motor Rated voltage ： 5VDC Number of Phase 4 Speed Variation Ratio 1/64 Stride Angle 5.625° /64 Frequency 100Hz DC resistance 50Ω±7%(25℃) Idle In-traction Frequency > 600Hz Idle Out-traction Frequency > 1000Hz In-traction Torque >34.3mN.m(120Hz) Self-positioning Torque >34.3mN.m Friction torque...

Creality 3D - 42-40 Stepper Motor * EXTRUDER motor til Creality 3D printere   Den kører på alle modellers Extruder   X-axis Y-axis Z-axis Extruder CR-10 Mini 42-34 42-34 42-34 42-40 CR-10S (300) 42-40 42-40 42-34 42-40 CR-10-S4 (400) 42-40 42-60 42-34 42-40 CR-10-S5...

4 Pin Cable - Female to Female - 70cm Extender Cable - 70cm   4 Pin Cable - Female to Female - 70cm

SpiderScrew Kit with Knurls - M3 - 80 pcs Vores nyeste SpiderScrew Kit. 80 pcs M3 skruer og 80 pcs knurls i forskellige størrelser.  *20 x M3-6 *20 x M3-10 *15 x M3-16 *15 x M3-20 *10 x M3-30   Forskellige typer M3 knurls:...

Creality 3D 42-40 stepper motor med dobbelt aksel  Anvendes på Y-aksen på Ender-5 og Ender-5 Pro Tabellen nedenfor viser, hvilken trinmotor der passer til hvilken akse på de forskellige Creality 3D-modeller:   X-axis Y-axis Z-axis Extruder CR-10 Mini 42-34 42-34 42-34 42-40 CR-10S (300)...

3D Printer Parts Dual Screw Rod Upgrade Kit Double Screw - Ex. Ender-3 V2 Præcis og glat skrue med høj præcision og lavet i høj kvalitet. Styreskinnens præcision er P3-P7. Den gentagne positioneringsnøjagtighed når 0,01 mm 3D Printer Parts Dual Screw Rod Upgrade Kit...

ULN2003 Driver Board ULN2003 Darlington using high-power stepper motor driver chip A, B, C, D four-phase LED indicates the status of the stepper motor work Stepper motor with a standard interface, when used directly pluggable. Dimensions : 31 x 35mm Package Include: 1x ULN2003...

SpiderScrew Mixed Kit - M3/M4/M5/M6 - 160 pcs Vores nyeste Spider Kit. 160 pcs M3/M4/M5/M6 skruer i forskellige længder.  *20 x M3-6 *20 x M3-10 *20 x M4-6 *20 x M4-10 *10 x M5-6 *10 x M5-12 *10 x M5-20 *10 x M5-30 *10...