MKS BASE V1.5 USB Compatible with Mega 2560 R3 Mainboard + Ramps 1.2

MKS Base V1.5 is the combination of Arduino MEGA2560 plus RAMPS1.4 and A4982 in 3D printer. It is a feature rich all-in-one electronics solution for Reprap and other CNC devices. It features an onboard ATmega2560. Its five motor outputs are powered by A4982 stepper drivers. It use FTDI FT232R device for USB and not ATMEGA16U2 as ARDUINO MEGA2560. The board can use the same firmware as Ramps1.4. MKS Base V1.5 is designed to be flexible in the user's power source availability, allowing any power supply from 12V-24V. It is supplied with a Marlin firmware. Of course you can also upload another firmware. You can use Arduino IDE to upload firmware to MKS Base V1.5 board through ICSP PIN.  While uploading the blue LED is lit and the RX/TX LEDs will blink fast.

Features:

• This is the combination for Arduino MEGA2560 + RAMPS1.4 + 5 x A4982 drivers (remix board)
• Arduino MEGA compatible Atmega2560 and FT232 processors are compatible with all RAMPS class firmware
• Firmware can use the same configuration as RAMPS1.4
• It is suitable for dual-Extrude printer
• Easy DISPLAY + SD-CARD connector, RepRapDiscount SmartController compatible pin header on  board
• 3x temperature ADC connectors for thermistors
• Up to 5 motor drivers with A4982
• 4x PWM capable power mosfet outputs  with voltage selector for MainPower.(Bed, Extruder0,  Extruder1, Fans)
• 4 layers PCB, optimize heat dissipation.
• 6x end stop connectors with power supply Xmin/Xmax/Ymin/Ymax/Zmin/Zmax
• Recoverable fuse for short-circuit protection.
• USB Driver Chip FT232RL, you can get files from ftdichip to setup driver: Ftdi-x86.zip

Fireware:
 

This section will show you how to get firmware into your controller and run it with basic settings.

Software required: FTDI USB drivers, for Arduino IDE, Choice of firmware (Marlin or Repetier or Sprinter), Pronterface

1. USB VCP Drivers - MKS Base uses the newer FT232 USB to UART chip and it needs the updated VCP(virtual com port) drivers from the
   manufacturer's website . Download the correct version for your operating system or you can get the executable version for Windows (easier).
   Windows Vista/7 may try to do an update to locate the proper drivers but it is recommended to install the FTDI drivers for better performance.
   The VCP drivers will install a COM Port on your computer  for the MKS Base, you can check what port number was  assigned by going to your device manager and click on  Ports(COM & LPT) look for something that says "USB  Serial Port(COM3)" where COM3 is you assigned port  number(will vary from PC to PC). Remember this number as you will be using it later in configuring other software.
2. Install Arduino IDE - Download and extract the Arduino IDE .
3. Get your firmware - While you can use most firmwares out there, we will use Marlin as an example. Download and extract Marlin or any other forks of the firmware that you prefer/need.
4. Upload firmware - Run the Arduino IDE (arduino.exe).
   Select your board - Click on Tools -->Board -->Arduino Mega 2560,
   Select your serial port - Click on Tools-->Serial  Port-->(select your COM port for the X3 USB, you can  check this in Device manager)
   On Arduino click File-->Open -- then point to your  Marlin Download and select Marlin.pde. With Marlin loaded on the IDE window, click on the tab that says "configuration.h".  These are the basic entries that you need to change to get the X3 working.
   
   #define BAUDRATE 250000 //This will work fine for the MKS Gen
   #define MOTHERBOARD 33 //33 is for RAMPS which the MKS  GEN is compatible with MOTHERBOARD 34
   #define TEMP_SENSOR_0 3 //If you have the NTC 100K
   #define TEMP_SENSOR_1 0
   #define TEMP_SENSOR_2 0
   #define TEMP_SENSOR_BED 3 //If you have the NTC 100K
   
   These entries are the only ones you need just to get the  MKS Gen running. Once you get it to upload you can now test most features of the board. You will need to tweak the settings on the configuration file for your printer.
5. Upload(or compile to test) Marlin  - While still on the Arduino window
   Click on the Triangle inside the circle to do a test  compile, this makes sure that the firmware does not  contain errors( you can skip this)
   Click on the arrow pointing to the right inside a square  frame to upload firmware to the board. If everything goes well you'll see a "Done Uploading" message near the bottom for Arduino window.

Package includes:

• 1 x MKS Base V1.5 3D Printer Controller Board  (MEGA2560 + RAMPS1.4 + A4982 remix board)

På linket nedenfor, finder du en mappe med alt dokumentation for 3D printere, filamenter mv. Den vil løbende blive opdateret

Klik her og gå til dokumentation

Du kan få leveret din ordre til en valgfri GLS pakkeshop, privats- eller erhvervsadresse.

Vi leverer din ordre fragtfrit til en valgfri GLS pakkeshop, hvis du bestiller for over 399 kr.

Du har mulighed for at vælge afhentning i butik. Når du modtager en mail med at din ordre er færdig pakket, kan den afhentes indenfor vores åbningstider, som er mandag til torsdag 9-17.00 og fredag kl. 9-16.30 på vores adresse Amalienborgvej 57 i Nørresundby.

Vil du vide mere om vores returregler, læs dem her

Vi ser frem til din ordre 😍